Anshuman Aerotech
Request Consultation

Testing & Calibration

The laboratory wheredoubt goes to die

Six NABL-accredited laboratories, 100+ qualification capabilities, and DGAQA approval — environmental, mechanical, vibration, electrical, coating, and battery testing under one roof.

Laboratory · ScopeISO 17025:2017
AccreditationNABL
ApprovalDGAQA
Laboratories6
Instruments90+
Thermal envelope−70 to +200°C
Shaker force6,000 Gf
DAQ channels80

01Six laboratories

Choose a discipline,open the lab door

Every laboratory below is NABL-accredited and DGAQA-approved. Select one to explore its instruments, capabilities, and governing standards.

Laboratory Profile

Environmental Testing

Climate simulation, humidity, rain, altitude and thermal testing

Showing 8 capabilities for Environmental Testing.

  • Temperature & Humidity Cycling: -70°C to +200°C, 10–98% RH
  • Thermal Shock (3 Zone): -65°C to +200°C, <10s transfer
  • Altitude / Low Pressure: Up to 3500L volume
  • Dust & Ingress: IP1X to IP6X per ISO 20653, IEC 60529
  • Corrosion: NSS, CASS, CCT per ASTM B117, MIL 810G
  • UV Aging: UVA 315–400nm, UVB 280–315nm
  • Xenon Arc: Accelerated full-spectrum weathering
  • Flammability / Ozone / SO₂ / Immersion
MIL-STD-810IEC 60068ISO 20653ASTM G154JSS 55555IS 9000

Full category detail →

Environmental Testing°C
Instrument register10 listed
01Vibration Shakers – 2 Nos
02Climatic Chambers – 11 Nos
03Thermal Shock Chamber – 2 Nos
04Dust Test Chamber (IP1X to IP6X)
05Corrosion Chamber – 2 Nos
06UVA/UVB Chamber – 1 No
07Xenon Arc Aging Chamber – 2 Nos
08Rain Chamber / Walk-In Climatic – 2 Nos
09Rapid Decompression Chamber
10Hot Air Oven

Environmental Testing

Climate simulation, humidity, rain, altitude and thermal testing

Capabilities

  • Temperature & Humidity Cycling: -70°C to +200°C, 10–98% RH
  • Thermal Shock (3 Zone): -65°C to +200°C, <10s transfer
  • Altitude / Low Pressure: Up to 3500L volume
  • Dust & Ingress: IP1X to IP6X per ISO 20653, IEC 60529
  • Corrosion: NSS, CASS, CCT per ASTM B117, MIL 810G
  • UV Aging: UVA 315–400nm, UVB 280–315nm
  • Xenon Arc: Accelerated full-spectrum weathering
  • Flammability / Ozone / SO₂ / Immersion

Instruments

  • Vibration Shakers – 2 Nos
  • Climatic Chambers – 11 Nos
  • Thermal Shock Chamber – 2 Nos
  • Dust Test Chamber (IP1X to IP6X)
  • Corrosion Chamber – 2 Nos
  • UVA/UVB Chamber – 1 No
  • Xenon Arc Aging Chamber – 2 Nos
  • Rain Chamber / Walk-In Climatic – 2 Nos
  • Rapid Decompression Chamber
  • Hot Air Oven

Standards: MIL-STD-810 · IEC 60068 · ISO 20653 · ASTM G154 · JSS 55555 · IS 9000

Mechanical Testing

Tensile, compression, impact, fatigue, and structural testing

Capabilities

  • Tensile & Compression: 50 KN to 600 KN capacity
  • Hardness: Rockwell, Vickers, Brinell
  • Impact: IZOD, Charpy, 1K Impact
  • Fatigue & Endurance: Connector, cable, push-button
  • Burst & Pressure: Hose burst, pressure hold
  • Shock: Up to 200g, half sine, saw tooth
  • Drop & Box Compression: Package validation
  • Displacement & Position Measurement

Instruments

  • UTM – 50 KN & 600 KN
  • Rockwell / Vickers Hardness Tester
  • IZOD / Charpy Impact Tester
  • Torsion / Torque Test Machine
  • Burst Pressure Test System
  • Drop Tester / Box Compression Tester
  • Shock Test Machine (up to 200g)
  • Cable Bend / Twist Fatigue Machine
  • Spring Compression Deflection Tester
  • 3 Point Bend / Ball Impact Tester

Standards: MIL-STD-810 · ASTM D638 · ISO 6892 · IS 9000 · JSS 55555

Vibration & Shock

Sine, random, shock, SOR/ROR and combined environmental vibration

Capabilities

  • Sine Vibration: Per IEC, MIL, JSS, ASTM
  • Random Vibration: Broadband random excitation
  • Shock Testing: Half sine, saw tooth waveforms
  • SOR & ROR: Sine-on-Random, Random-on-Random
  • Resonance Search & Dwell: Endurance testing
  • Combined Vibration + Climatic: Temp + vibration
  • Acceleration Measurement: B&K system
  • Noise / Sound Measurement

Instruments

  • Vibration Shakers (3 Axis, 6000 Gf Force)
  • Vibration Integrated Climatic Chamber
  • Shock Test Machine (up to 200g)
  • Accelerometer Calibration System (B&K)

Standards: MIL-STD-810 · IEC 60068 · JSS 55555

Electrical & Connector

Dielectric, continuity, resistance, and connector qualification

Capabilities

  • Insulation & Contact Resistance
  • Dielectric Withstanding Voltage (Hi-Pot)
  • Voltage Drop Across Contacts
  • ES Discontinuity: Millisecond detection
  • Insertion / Release / Coupling Force
  • Insert Retention & Maintenance Aging
  • Temperature Rise Under Load
  • Multi-channel Datalogging (80 channels)

Instruments

  • AC/DC Withstanding Voltage Tester
  • Micro Ohm Meter / Agilent DMM 34401A
  • Resistive Load – 10+ Nos (up to 4kA)
  • Power Supply – 30 kW, 1000A
  • 80-Channel Datalogger
  • ES Discontinuity Meter
  • Power Meter – Yokogawa WT230
  • Fluke Scope Meter 123

Standards: MIL-STD-810 · IEC 60068 · JSS 55555

Paint & Coating

Corrosion, weathering, adhesion, and surface finish evaluation

Capabilities

  • Salt Spray: NSS, CASS, CCT per ASTM B117
  • UV Aging: UVA/UVB per ASTM G154, G151
  • Xenon Arc: Full solar spectrum aging
  • Scratch & Mar Resistance
  • Gloss & Colour Measurement
  • Adhesion: Cross-cut, Pull-off
  • Coating Thickness: Dry film measurement
  • Thermal Cycling for Coating Durability

Instruments

  • Salt Spray / Corrosion Chamber
  • UVA/UVB Weathering Chamber
  • Xenon Arc Aging Chamber
  • Hot Air Oven / Gloss Measurement
  • Colour Matching Cabinet
  • Scratch Resistance Tester

Standards: ASTM B117 · ASTM G154 · ASTM G151 · IS 9000 · MIL 810G

EV Battery Testing

Electrical, thermal, mechanical and safety validation for battery systems

Capabilities

  • Charge/Discharge Profiling
  • Vibration per UN 38.3, MIL-STD-810
  • Mechanical Shock for Battery Packs
  • External / Internal Short Circuit
  • Thermal Cycle & Thermal Shock
  • Overcharge / Overdischarge Protection
  • BMS Safety Protection Validation
  • IP Ingress Protection (Dust & Water)

Instruments

  • Battery Charge/Discharge System
  • Vibration Shaker with Climatic Integration
  • Mechanical Shock Test Machine
  • Thermal Shock Chamber
  • Charge/Discharge Cycle Tester
  • IP Enclosure Test Chamber
  • Withstanding Voltage Tester

Standards: UN 38.3 · MIL-STD-810 · JSS 55555 · IS 62619:2017

02Verification

Check us beforeyou commit

Every claim on this page is meant to be verified, not taken on trust. Where a reference is not yet published here, it is available on request.

Accreditation recordOn request
AccreditationNABL, per ISO/IEC 17025:2017
Certificate numberAvailable on request
Scope of accreditationIssued on request, under NDA
Certificate validityAvailable on request
ApprovalDGAQA
DGAQA referenceAvailable on request
Quality systemISO 9001:2015
Aerospace QMSAS9100D
Special processNADCAP
Design organisationEASA Part 21
Authorised signatoriesNamed on issued reports

Certificate numbers, current scope and signatory authorisations are issued directly to procurement and quality teams on request — normally alongside a mutual NDA. Ask the tender helpdesk and they arrive the same working day.

03Standards

Qualified against thestandards that decide programmes

MIL-STD-810

Environmental engineering for defence and aerospace equipment

Defence, Aerospace, Military Systems

ISO 17025:2017

General requirements for testing and calibration laboratories

All Testing & Calibration

IEC 60068

Environmental testing procedures for electrotechnical products

Electrical, Electronics, Components

IS 9000

Indian Standard for environmental testing of electronic equipment

Electronics, Defence, Aerospace

JSS 55555

Joint service specification for environmental testing

Defence, Joint Services

UN 38.3

Transport of dangerous goods - lithium battery testing

Battery, EV, Logistics

IS 62619:2017

Industrial standard for secondary lithium cells and batteries

Battery, EV, Ground Power Systems

Accreditations and approvals we hold

ASTM International

Standard test methods for materials, products, and systems

NABL ISO 17025

National Accreditation Board for Testing Laboratories

DGAQA Approved

Directorate General of Aeronautical Quality Assurance

04Test-to-certificate workflow

Six steps, zeroambiguity

01

Client Requirement

Define test objectives, applicable standards, and acceptance criteria with your engineering team

02

Test Planning

Develop comprehensive test plan with parameters, fixtures, instrumentation, and scheduling

03

Laboratory Execution

Conduct tests per approved procedures with real-time monitoring and data acquisition

04

Engineering Validation

Analyse results against specifications, validate pass/fail criteria, and review with engineers

05

Certification Report

Generate NABL-accredited test reports with full traceability and certificates of compliance

06

Customer Delivery

Deliver comprehensive test documentation, certificates, and post-test engineering support

05Engagement terms

What you get, andwhat it takes

The commercial and practical terms behind a qualification campaign, stated before you ask.

01Turnaround

Standard environmental tests complete within 5–10 working days. Comprehensive qualification programmes require 4–8 weeks, depending on test complexity and scope.

5–10 days / 4–8 weeks
02Expedited & recovery programmes

Expedited scheduling and parallel testing are available for schedule-critical programmes, including recovery plans after a failed qualification elsewhere.

On request
03Confidentiality

We routinely execute mutual NDAs before technical discussions. Request one in your first message and we will send our standard template.

Mutual NDA
04Witnessed testing & laboratory tours

Laboratory tours are available by appointment at our Panchkula facility, and witnessed testing can be arranged for your quality representatives.

By appointment
05Calibration & competence

All testing is performed by certified engineers using calibrated instrumentation. We maintain comprehensive standards libraries, and our procedures are regularly audited by accreditation bodies.

ISO 17025 discipline
06Documentation

Every test is documented with full traceability — instrument IDs, calibration records, raw data and engineering analysis — issued under the NABL ISO 17025:2017 accredited scope.

Full traceability

06Who we test for

From flight lines torail lines

The same laboratory standard serves twelve sectors — from military and civil aviation to space, automotive, railways, marine, electronics and energy. Each has a dedicated capability profile.

Military Aviation

MIL-STD qualification & environmental testing for defence aircraft and systems

Civil Aviation

Environmental and electrical qualification testing for commercial aircraft components

Space

Vacuum, thermal cycling, and vibration testing for space-grade hardware

Automotive

EV battery, environmental, and electrical testing per applicable industry standards

Electronics

IEC 60068 environmental & electrical testing for electronic assemblies

Railways

JSS 55555 and IEC environmental testing for railway electronics and systems

Marine

Corrosion, salt fog, and humidity testing for naval and marine equipment

Energy

Battery safety, renewable components, and grid equipment qualification

Explore the twelve sectorsDedicated capability profiles

Schedule the test thatsettles it

Send your test matrix and standard — we return instrument allocation, timeline, and a fixed quotation.